Odin connects once a day via either a 4G or local Wifi network to send you a staus update. 

The standard Odin system can be connected to any local wifi network as long as you have the SSID and password, and you are within the range of the wifi network router. 

If you require a 4G enabled Odin, you can select this option in our online store. For a small additional cost we will include a 4G modem dongle, and connecting cable, to your system. 

You will need to buy a pay-as-you-go, or monthly contract, SIM card and activate it, before installing it into Odin’s dongle modem. 

Please see this post to view more information about Odin and 4G. 

Absolutely! Any C or CS mount lens can be used. The physical limit for your lens is approx 100mm in length and the case portal diameter is 52mm. The system is supplied with a C-CS lens adaptor.

Odin has a “live preview” button utility in its user interface. Just hit this button to view the focal point while manually adjusting the lens. You can also use this feature creatively if you choose.

Yes, you can. Any 67mm lens filter can be used. It is worth noting that, if you do change the supplied lens filter, you must check the lens O-ring is sufficiently seated for a watertight seal. This is especially important if you plan to use your camera for outdoor, long-term, projects

The Odin user interface can be accessed by toggling the switch on the rear of the camera to the “Setup” position. On any suitable laptop, tablet, or mobile device just log into Odin’s wifi network, then enter the interface IP address (192.168.99.1) into your browser address line. Always remember to “save” your settings before you start your new recording sequence!! 

Short-term mode allows you to take images at a fast interval, 1sec, or even less. To achieve this, the system stays powered on with a maximum runtime of approx 48hrs using the internal battery alone.  

Long-term mode allows you to take images down to a 1-minute interval. The system shuts down in between taking images to save power. When using the supplied solar panel with this mode it is possible to run Odin indefinitely. 

There are three ¼” UNC mounting points on the bottom of the camera case. Any standard ¼” photographic mount or bracket can be used. The weight of the system is approx 1.3Kgs.

Solar panels are mounted separately so they can be placed in an optimal position for direct sunlight. The mounting thread is ¼” UNC, and standard photographic / CCTV brackets can be used. 

The camera is supplied with a 12V 5W solar panel and 2m of cable. Additional 2m cables can be added, but we would not advise extending more than 10m (due to voltage drop). 

Furthermore, solar power input can be increased to a maximum of 20W if required. Using panels in excess of 20W is not advised as this could damage the solar charge controller.

It’s very simple to add additional power sources to Odin’s internal UPS (uninterrupted power supply) battery. You can either add a Micro USB external 5V supply to the battery for a constant supply, or you can add additional 12V solar panels for increased charging capacity. 

Yes, absolutely!  The case has been certified IP66 which means it can withstand direct water ingress. The system has also been tested to a constant -15°C for 48hrs with no operational problems. 

We are a small company, but that doesn’t mean we can’t personally help you if you have questions, or need a little technical help. You’ll find an Odin support page on this website, and we’ll be adding help, instructional videos and advice to this page over the coming months. In the meantime, just drop us a line via email, or phone, if you have any unanswered questions.

We’ve made Odin as reliable as possible, but if you have any manufacturing or defective components, we will happily replace, repair, or refund the problem part within 6 months of purchase. This warranty is limited to fair and reasonable usage. User modifications might affect this warranty. 

Again, the beauty of Odin is that it is a modular system so it is relatively easy to replace any defective component. 

We have systems made and ready to ship, but if your system is being made to specific requirements you may have to wait 1-2 days for your system to be built. 

Domestic orders will be shipped via signed Royal Mail, and international orders will be shipped via tracked DHL. Duty and Vat customs will be forward paid by the purchaser (DDP) to expedite the shipping process.